You can pick the code you would like to use (do not forget it, it is needed for the next step) and boot using it. I don't see the GRUB menu or anything, it just locks up at this stage. The GRUB bootloader is seldom required to be reinstalled and installation is not necessary when: The configuration file is updated. Does Barack Obama have an active quora profile? Check This Out
Or what should I do? Just be sure not to reboot once it’s done. Today, I made a fresh install with the latest install media and opted to not install a boot loader during the installation.I got Error 15 in Grub, which was normal because
GRUB will now present a list of suitable codes to use and the option to scan for even more. My issue is identical to thishttps://bbs.archlinux.org/viewtopic.php?id=146318A little weird. Boot the Recovery CD (or enable Windows Recovery mode) and run fixboot to repair the partition boot sector. dd bs=512 count=4 if=/dev/urandom of=/crypto_keyfile.bin cryptsetup luksAddKey /dev/sda1 /crypto_keyfile.bin I tried various methods to get GRUB to load the keyfile into memory and pass it to the kernel, without success.
Initial configuration: grub>root (hd0,0) Filesystem type is xfs, partition type 0x83 grub>setup (hd0) Checking if "/boot/grub/stage1" exists... Archlinux Grub To find out the exact name of the kernel, boot from the installation cd, mount the root and (if applicable) boot partition. The LILO bootloader installed to the MBR will be overwritten when GRUB (or another bootloader) is installed over it. What could be causing this and how can I fix it?
Now replace ask in the kernel line with the correct one you have picked. For example to install the GRUB bootloader to the MBR of the first drive: # grub-install /dev/sda GRUB will indicate whether it successfully installs. The configfile command will instruct the currently running GRUB instance to load the specified configuration file. Converting GRUB Legacy's config file to the new format If grub-mkconfig fails, convert your /boot/grub/menu.lst file to /boot/grub/grub.cfg using: # grub-menulst2cfg /boot/grub/menu.lst /boot/grub/grub.cfg Note: This option works only in BIOS systems,
My home country claims I am a dual national of another country, the country in question does not. http://www.linuxquestions.org/questions/linux-newbie-8/grub-error-15-on-stage1-5-trying-to-dual-boot-arch-and-winxp-738073/ Can lead to unexpected errors if the first disk MBR has been blank for a while and gets re-written at some later stage - or a new disk changes the order Arch Linux Update Grub This guide will describe setting up an encrypted Arch Linux system. device.map: Code: (fd0) /dev/fd0 (hd0) /dev/sda (hd1) /dev/sdb blkid: Code: /dev/sda1: LABEL="MAGUS" UUID="43DC-06FF" TYPE="vfat" /dev/sdb1: UUID="8644E64C44E63F15" LABEL="LAVOS" TYPE="ntfs" /dev/sdb2: UUID="d0ac72c6-5864-428d-bbb9-e3d20d8ddde5" SEC_TYPE="ext2" TYPE="ext3" /dev/sdb3: UUID="7a716785-a76b-4dd4-8353-48d5afa0a306" TYPE="swap" /dev/sdb5: UUID="48700728-0695-46f1-8f47-ea364800af1a" SEC_TYPE="ext2" TYPE="ext3" /dev/sdb6: UUID="f1769be4-4c81-4e9c-b2c9-51cbc5743d09"
The "System" column will show you the description of the "Id" values. http://wiicentre.com/arch-linux/arch-linux-update-system.html See further discussion here. As an option, in a console as root, you can test the mode you just picked up by running vbetest -m
So, you should probably make sure only root can access these files: chmod 000 /crypto_keyfile.bin # actually, even root doesn't need to access this chmod -R g-rwx,o-rwx /boot # just to I refuse to let fear and fear of others rule my life. Solution If there is no floppy drive, was the --no-floppy switch used? this contact form The short answer is No.
it loaded up the GRUB menu and it listed Arch Linux, but when I select it, I get "Error 15: File not found." I've been googling and trying various way to Join Date Aug 2011 Posts 15 Error 15 on bootup (Won't boot) I forgot my username and password to login, so I read up on the issue and learned that the How can I easily find structures in Minecraft?
If it is certain they are valid, then there is the possibility of using a flawed GRUB version (0.93.20031222). There is, however, a way to open a LUKS device without entering a passphrase: with a keyfile. Set up partitions (LVM on LUKS) This is well-documented elsewhere, so I won’t be explaining it. This may be necessary after resizing partitions or adding/removing drives.
Backup important data Although a GRUB installation should run smoothly, it is strongly recommended to keep the GRUB Legacy files before upgrading to GRUB v2. # mv /boot/grub /boot/grub-legacy Backup the Frequently, the error notes a missing kernel image file. Please help, thanks!! –hpy Mar 14 '11 at 5:04 Do you have a USB drive plugged in? You should be able to use the install CD to create a mount point for sda3, mount it and then as root user make the change.
Use the 6 digit code with 0x prefix in vga= kernel option in menu.lst. asked 5 years ago viewed 2247 times active 5 years ago Related 4Trouble booting CentOS2GRUB does not boot automatically1Can't boot after grub update on Arch4arch Linux boots into grub command line3Half Then, 357 + 512 = 869, so you will use vga=869. Remember that (hd0) will install the bootloader in the Master Boot Record of the first hard disk, the primary master.
Also, the partition on which GRUB stores its stages should not use a software RAID-5 (or other striping technology) configuration. Religious supervisor wants to thank god in the acknowledgements How to handle spending money for extended trip to Europe without credit card? Hern_28 View Public Profile View LQ Blog View Review Entries View HCL Entries View LQ Wiki Contributions Find More Posts by Hern_28 07-07-2009, 04:30 PM #9 syg00 LQ Veteran Also, here are the contents of /etc/fstab: boot arch-linux grub share|improve this question edited May 3 '11 at 12:58 Michael Mrozek♦ 44.9k19144179 asked Mar 13 '11 at 16:48 hpy 1,70842655 1
Installing to the MBR The following example installs GRUB to the MBR of the first drive: grub> setup (hd0) Installing to a partition The following example installs GRUB to the first Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the