If your display is reading "wait" for longer than 6 minutes I would suggest contacting the manufacturer directly at 800-822-7933 for further assistance trying to identify the issue. Fiddlerman Thanks 🙂 Shawn I am not getting any code it says wait, either to much pressure and then it goes down to low pressure is the pump going out? If that doesn't work then I will order a new sensor. Swimming Pool Tips, Reviews & How To -MrDgvb1 7,343 views 2:18 How to clean your Jandy cartridge filter - Duration: 6:56. Check This Out
So I wonder if the screen just needs new calibrating? If you are a service tech, i would take a little capital, and buy a sensor to keep with you, so you can do some faster diagnostics. Reduce water temperature 175 Flow sensor air lock condition or very low salinity Verify proper flow/temperature/salinity sensor installation. Transcript The interactive transcript could not be loaded. http://www.poolsupplyworld.com/blog/jandy-aquapure-troubleshooting-error-codes/
Is it possible that the lack of water circulating through the cell has caused the cell to become damaged? PM sent Share this post Link to post Share on other sites Create an account or sign in to comment You need to be a member in order to leave a After I put it all back together it is only throwing one code, 144 for low salinty. If damaged replace parts or entire unit.
If there is buildup or no apparent issues then proceed to step 2. 2) Clean cell in a mixture 4 parts water and 1 part acid, rinse with fresh water when John My PureLink System (AquaPure PLC1400 + AuqaLink RS) system was giving codes 175 & 182. Add to Want to watch this again later? Aquapure Error Code 125 194 Additional Letter Service Codes: Code Condition Reason EC External Control ORP unit or external controller has shut off chlorine production.
Only because the Jandy A/P sensors have been having these problems lately (over the past 18 months) and replacing the sensor has been fixing the problem. I am having the exact same problem.. Ted Melcher Getting 175 error code. After completing steps 1-4, if there is no solution to the issue, it is always helpful to contact the manufacturer directly at 800-822-7933.
For example, the first time you install and start the system this "wait" period can last a few minutes as the system and the sensor attempt to calibrate. Jandy Aquapure 170 Error Code I bought the sensor off E-bay from a location in California. Problem is AquaLink PDA no longer registers the AquaPure. This should not be directly related to the pump unless the pump is turned off or has very low flow, and thus the system is having a hard time calibrating the
Release the button after the 3rd beep. •Press and release the “Temperature “button within 5 seconds to enter the salinity calibration screen. •The system will display the salinity reading, press the http://www.poolspaforum.com/forum/index.php?/topic/36299-jandy-aquapure-issue-front-board-or-sensor/ I contacted our rep at the manufacturer and she did state she has never heard of that before. Aquapure Error Code 145 The service light is on and codes 172 and 185 are displayed. Aquapure Error Code 120 You can see the different configurations on page 9 of the Owner’s Manual found on the three-port Cell Kit for Pools up to 40,000 Gallons product page.
The connector between the PCB and the Multiplex board is good. http://wiicentre.com/error-code/jandy-aquapure-error-code-172-181.html Sign in to make your opinion count. There is no test right now to check just the flow sensor though. Factory Warranty Station for: Jandy, Pentair, Sta-Rite, Raypak, Polaris, and Paramount pool cleaning systems. Jandy Aquapure Error Code 120
Results 1 to 7 of 7 Thread: Need HELP Service Code 144 - Jandy Aquapure Thread Tools Show Printable Version Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode Jandy Aquapure Error Codes The flow light is not on and the salinity reading is --. Both codes of 172/186 share the same meaning.
Please clarify. How old is the cell? - Christian Wayne Coates I have a 1400 and this year had to replace my chlorine sensor as our dog ate off the wires. Please try the request again. Jandy Aquapure Code 170 I recently starting getting codes 172 & 186, then 172 & 181.
stanley Mazurek Hi,I'm new to my Jandy pool system and recently got strange number on the display that is #39 and light is lit (cell reversing Plus service) checking the codes Clean filter and make sure there are no blockages. Saludos Tony Share this post Link to post Share on other sites Pool Clown 0 Spa Guru Members 0 2,685 posts Gender:Male Location:Silicon Valley, CA Gender:Male Posted June 10, 2012 navigate here The system returned: (22) Invalid argument The remote host or network may be down.
Dylan (PoolSupplyWorld) First step I would take is to clean the sensor per the instructions in the manual.