Release the printer locking screw. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. The CDU belts or the Cassette rollers may need to be cleaned (rubbing alcohol). Make sure the electrical connections to the timing wheel sensor are secure and the time wheel sensor is clean. http://wiicentre.com/error-code/att-error-code-668.html
Loose belts can slip off rollers and block sensors. 21B15 CDU detects bills prior to dispensing This means that while the ATM was initializing it detected a blocked sensor in the Recommended Action: This error is reported when the transmission of each one of the characters in the command string is not completed within the time restriction imposed by the electrical interface. Replenish the paper. Refilling may be delayed for several transactions if the error code is the first warning that the cassette is nearly empty. http://www.atmexperts.com/atm_error_codes.html
If the status clears and the return code are normal place the cash dispenser in service. Inspect the detent clips (the clips that hold the cassette in place). Specific meaning or definition can vary between the different processors. D0043 Stolen Card Code reported by host processor (Shazam).
Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. Contact host processor D00A6 FS omitted (after total non cash dispense amount in day close) Verify all programming. Remove the cassette and visually inspect for loose or disconnected connectors on both the upper and lower width sensor printed circuit boards. 3. Atm Error Code 3-da001 Inspect electronic journal to dispenser communication cable for damage.
Inspect the printer data cable for damage. Error Code 3-d1500(00) Doing this will not clear any available memory, and will not aid in clearing Error Code 151.) Below are steps to take to clear Error code 151 on 32-bit machines: 1. Test the dispensing mechanism by completing several test dispenses. http://www.accessatm.com/service/atm-error-codes/triton-error-codes/ If the error code continues, replace the note transport module.
Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error. Atm Error Code 3-da000(80) Reset the error. Inspect for jammed currency at the Exit. Recommended Action: Remove the cassette and inspect for jammed currency in the width sensor and at the output of the cassette.
Inspect main board to electronic journal communication cable for damage. Purge the dispenser. Atm Error Code D1706 Error Code: 105 (69h) Description: Insufficient notes to learn from Recommended Action: There may be an insufficient number of notes in the cassette to complete the requested “learn note thickness” command. Atm Error Code 3-d1500 Perform a live transaction.
If excessive rejects are suspected, see corrective action for Error Code 48. 3. news If it clears, initiate the learn note thickness operation. A temporary fix to this problem may be to set the â€ślow receipt paperâ€ť parameter to â€śin serviceâ€ť so that the terminal software does not read the input from the low If no bills are present try using compressed air to clean the dispenser (a sensor may be blocked by dust). No Eot Received From Host
D0061 Exceeded withdrawal limit Code reported by host processor. D1100 ENQ not received from host Verify all programming. Error Code: 165 Description: Electronic journal not present. http://wiicentre.com/error-code/error-code-200-eso.html Purge the dispenser using the purge command.
Cassettes are taken out of service because of feed failures or excessive rejects. 1. Hyosung Atm Error Codes Excessive EMI emissions from outside source (neon sign, freezer). Make sure the ribbon cable from the docking station to the card reader is fastened at both ends of the cable and the orientation of the cable is correct.
Do several test dispense operations. 4. Error Code: 363 Description: Dispenser device not found Recommended Action: Restart the operating system. Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error. Atm Error Code 3-da000(20) Make sure the connectors are seated securely on the main board and on the electronic journal. 4.
Recommended Action: This error code occurs when the message received by the dispenser is incorrect. Verify that all DC voltages applied to the printer control board are correct. Contact host processor D009E FS omitted (after retrieval reference number) Verify all programming. http://wiicentre.com/error-code/ast-code-of-ethics.html If these actions have no effect on dispenser operation, replace the dispenser mechanism.
Audited records can then be archived to an external device or deleted. (Note: Records can be archived to the internal flash. Inspect all cables for damage.