If error persists, replace the dispenser mechanism. If the cash dispenser operates normally put it in service. Make sure they are seated at the printer control board and not damaged. 6. Inspected both the feed sensor and the double detect sensor to ensure they are not blocked and operating correctly. http://wiicentre.com/error-code/triton-atm-error-code-101.html
a. Make sure the tamper screw is secure to the SPED module. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. On 96XX models, open the printer access latch and inspect for jams and blockage. 8. . http://www.accessatm.com/service/atm-error-codes/triton-error-codes/
Remove jammed currency. 2. Verify that the power supply is operating and the DC voltages being supplied to the main board and dispenser are correct. Reset the cash dispenser. Error Code: 164 Description: Terminal did not return call. (Triton Connect error) Recommended Action: This error is not displayed at the cash dispenser.
Error code 320 will not put the cash dispenser "Out of Service. If any sensor is out of its calibration limits, clean all of the sensors and attempt to do a transaction. Inspect all cables for damage. Atm Error Code F0001(00) Start by verify your communications settings and external TCP-IP equipment. 2.
Inspect all documents for excessive wear. Atm Error Code 3-da001 If the problem persists, replace the dispensing mechanism. Clear all errors and PURGE the dispenser. 4. Check This Out Do several test dispense operations.
Clear the error. 2. Atm Error Code 3-da000(20) The Triton Connect Host Computer generates this error when a terminal does not return a call to the Triton Connect Host Computer as requested. All the above actives may result in the deletion or corruption of the entries in the windows system files. The journal on these machines should be printed on a regular basis (i.e.
If these actions have no effect, replace the dispenser. 44 Bad Roller Profile This status is generated if the double detect is unable to calibrate. More Help Inspect all cables for damage. Error Code 130 Triton Atm Clean as needed with soft brush and vacuum cleaner. 2. Atm Error Code 3-da000(80) This problem may be caused by incompatibilities between terminal software and dispensing mechanism software.
Triton Atm Error Code 130 Error Codes are caused in one way or another by misconfigured system files in your windows operating system. http://wiicentre.com/error-code/error-code-200-eso.html Purge the dispenser using the purge command. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. Proceed by following procedures for error code 109 or 112. 108 Unexpected note at double detect A note has been detected in the double detect sensor without being detected at the Atm Error Code 101
Recommended Action: Inspect main board to Electronic Serial communication cable for damage. Allowable bill sizes are 5, 10, 20, 50, and 100. Error Code: 152 Description: Electronic journal corrupt. have a peek at these guys Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser.
Install the Reject Vault. Atm Error Code D1706 Make sure the ribbon cable from the docking station to the card reader is fastened at both ends of the cable and the orientation of the cable is correct. If the error clears put the cash dispenser into service.
Error Code: 14 Description: BGD DONE BAD Possible Cause: 1. Inspect the printer data cable for damage. Recommended Action: This status occurs when a note is detected by the exit sensor when it should not have been. Atm Error Code 3-d1500 It can also be caused if your computer is recovered from a virus or adware/spyware attack or by an improper shutdown of the computer.
If these actions have no effect, replace the dispensing mechanism. Purge the dispenser using the purge command. If these actions have no effect on dispenser operation, replace the dispenser mechanism. check my blog If the error clears, put the cash dispenser in service. 3.
Remove and empty the reject vault. Error Code: 119 (77h) Description: Diverter in dispense position on start of dispense or learn Recommended Action: 1. If all sensors are operation correctly, and the error persists, replace the replace the dispenser. Verify that the diverter moves freely. 3.
Error Code: 304(34h) Description: Rejected notes. Error Code: 366 Description: Dispenser cassettes disabled. Recommended Action: This Error Code is valid for units with SPED keypad device installed. Recommended Action: Restart the operating system.
Enter management functions and verify that all terminal parameters have been entered correctly. 2. Install the note feeders and recheck their operation to determine if the error code has been cleared. Clear the jammed documents.2. If the voltages are correct, and the cables are undamaged and correctly connected, causes of this error may be a defective cable, a defective printer, printer control board or the main
Remove the jammed documents as needed. Recommended Action: This error code indicates that notes were rejected during the transaction or test dispense operation. Error Code: 109 (6Dh) Description: Time-out at Exit sensor Recommended Action: 1. Make sure the documents are fit condition.
Reset the error. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 104 Unable to clear width sensor. Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Recommended Action: This error is produced when a sensor in note transport module is not working correctly during an internal self-test preceding the movement commands.
Error Code: 54 (36h) Description: Operation time-out Recommended Action: 1. Error Code: 349(61h)[a] Description: Cassette lock faulty. Error Code: 35 (23h) Description: Mistracked note at double detect.