Phone line is in use or is being shared with another phone device (FAX, POS, phone). Do RESET at Operator Function2. Check second Dip Switch in Cash Dispenser B/D 3. Look for the bill jam very thoroughly. 40021 Pick up error This error happens if there is no money in the machine but there is money in the software 40022 Over this content
Exchange Sensor after abnormal operating CS15A Sensor 4003B00When CS15A or CS 15B sensor is detected as dark after initial recovery_ Remove notes or dust in existence CS15A Sensor _ Check CS15A Inspect the currency for excessive wear. Exchange a sensor after abnormal operating the CS37 sensor . 4009F3 cassette miss feed error 4009F3 Cassette miss feed during dispense operation1. Error Code: 32 (20h) Description: Good operation Recommended Action: No action required. http://www.atmexperts.com/atm_error_codes.html
Use the diagnostic functions or NMD test software to determine if a note feeder has a faulty or dirty sensor. Specific meaning or definition can vary between the different processors. Reboot ATM 2.
Purge the dispenser using the purge command. Recommended Action: This error code indicates that the system has recognized a document intended for the reject vault has reached the note transport sensor. Check the remaining notes in 2 Cassette2. Hyosung Atm Error Codes It was detected that the feed lever was open before ther receipt printer started to operate.Clear jammed notes or call your service personnel. 20016Note detected in stacker (shutter or presenter type)Clear
If this error is consistent, the printer or mainboard may require service. Error Code 3-d1706 Check if the CIU power cable is connected. 90001Card Swipe Error.This error shows the number of times a customer swipes their cards unsuccessful. 97120Unable to create INI file 97121Unable to read If any sensor is out of its calibration limits, clean all of the sensors and attempt to do a transaction. page This occurs when the currency in any cassette reaches a thickness of approximately 25-35 mm.
Inspect for jammed Currency in the feed path and at the Exit sensor. Atm Master Codes Exchange a sensor after abnormal operating the CS31A, CS31B sensor 4009CDetected the CS31B Dark during initializing or dispense reserved operation1. Reset the machine if problems persist, please contact the service provider 40051 BCC error Hardware failure. Seat connectors or replace the power supply as needed. 2.
Check the cable and connections from J7A on the docking station to the SPED board. 210 Dispenser type unknown See Error Code 130 236 Failed to make connection to TCP/IP host http://www.completeatmservices.com.au/error-codes.html Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. Triton Atm Error Code 101 Check the status of setting paper 2. Atm Machine Code In C++ Error Code: 148 Description: Write to electronic journal failed.
Remove a jammed note in 4 Cassette.2. http://wiicentre.com/error-code/error-code-200-eso.html Reset the machine, if problem persist, please contact the manufacturer. 2G4C2 Head open error Close the printer header and press reset 2G4C3 Head Temperature Error Check Header 2G4C4 Cutting Error Parts Reset the machine if problems persist, please contact the service provider 43030 Reject rate exceed Hardware failure. Please contact the manufacturer if these error happens 5G001 Port Error on Status Check the connection of the Modem cable, if problem persist replace the modem, cable or the port 5G002 Hack Atm Machine Code
C00E0 NS2A, NS2B dark Nanocash only - verify connections to sensors. Remove any unacceptable notes from the cassette. 2. Error Code: 119 (77h) Description: Diverter in dispense position on start of dispense or learn Recommended Action: 1. have a peek at these guys D0084 Processor not available; acquirer processor unable to send message Code reported by host processor.
Error Code: 161 Description: Electronic journal clear feature failed. Atm Error Code 3-da001 Check the Cutter module 2. One or two instances of this error does not usually indicate a defective part.
If the sensor is properly connected and operating correctly the CMC module may be defective. If persistent, it could be a defective modem. Error Code: 109 (6Dh) Description: Time-out at Exit sensor Recommended Action: 1. Atm Error Code 3-da000(80) Inspect the currency for excessive wear.
Clean CS4A and CS4B 4001CCS4A and CS4B Dark detection during initializing or dispense reserved operationThe same as #40014 and #40018 error handling 4001C00Detecting CS4A, CS4B Dark 4001DCS2, CS4A or CS4B sensor Purge the dispenser using the purge command. Remove any jammed currency. 2. check my blog Clear all error and purge the dispenser using the purge command.3.
Error Code: 325(49h)[I] Description: Note qualifier faulty Recommended Action: Error code 325 is generated when the double detect sensors in the note qualifier can not be calibrated, or when the gain Reinstall software3. Cracked or broken clips should be replaced 4. Note: If the modem is defective, this error will most likely occur frequently.